Products

Axial Fans

FUBD Roof Exhauster

FUBD Roof Exhauster
Description will go here.
Product Specification
Specification will go here!

FTAB Tubeaxial Fan

FTAB Tubeaxial Fan
  • 13 Sizes : 12.0" to 60.0" ~ 300mm to 1524 mm
  • Volumes : 600 - 80,000 cfm ~ 0.28 - 37.77 m3 /s
  • Pressures : to 2.0" wg ~ 500 Pa
  • Maximum temperature 160F ~ 72C
  • Arrangements 4 and 9

The fixed pitch airfoil designed wheel of the FTAB Tubeaxial Fan optimizes performance whilst offering solid frp composite construction throughout giving increased life expectancy in arduous corrosive environments

Available model sizes (click for details):
120 150 180 210 240 270 300 330 360 420 480 540 600
Product Specification
  • Fans to be FRP composite construction tube axial fan model FTAB as manufactured by Universal Fan & Blower Ltd. and shall be fabricated in accordance with ASTM Standard Specification D416797 (reapproved 2002) for Fiber Reinforced Plastic Fans & Blowers and CGSB 41-GP-22 Standard for Process Equipment.
  • Fan housing shall be of solid FRP composite construction, fabricated by open molded methods using vinyl ester resin and glass veil to be used on all airstream surfaces giving a resin rich liner for optimum chemical resistance. A reinforcing flange shall run the external length of the housing to provide additional strength. The housing shall be flanged at both ends for duct connection and is equipped with an adjustable motor support plate for drive tensioning
  • The fan wheel shall be solid FRP composite molded construction and of a true airfoil design to maintain aerodynamic efficiencies. The wheel shall be positively locked onto the shaft by means of a 316ss retaining plate. [Taperlock bushings are not acceptable.]. The wheel shall be balanced statically and dynamically as per ANSI/AMCA Standard 204.96 Balance Quality & Vibration Levels for Fans to grade G 6.3.
  • Shafts will be 316ss accurately turned & gauged for accuracy and sized so that the first critical speed is a minimum of 1.35 times the maximum operating speed.
  • Shaft Seal shall be Teflon precision cut for a close tolerance fit with the fan shaft, encased within an FRP seal box with encapsulated 316ss fasteners.
  • Bearings shall be pillow block design sized to have a minimum life of 50,000 hours based on AFMBA L10 standard. Bearings shall be equipped with extended lubrication lines with grease fittings on the outside of the fan housing.
  • All fasteners to be 316 stainless steel construction.
  • The exterior of the fan shall have a grey gel coat finish containing U.V. inhibitor to prevent ultra violet light degradation.
  • Prior to shipment all fans shall be mechanically test run and trim balanced to ensure vibration levels are in keeping with ANSI/AMCA Standard 204.96.
  • Note: The addition of UFBL Features to the standard fan will amend the specification accordingly

    Standard Product Specification FTAB-111207

    FUBB Roof Exhauster

    FUBB Roof Exhauster
    • 13 Sizes : 12.0" to 60.0" ~ 300mm to 1524 mm
    • Volumes : 600 - 80,000 cfm ~ 0.28 - 37.77 m3 /s
    • Pressures : to 2.0" wg ~ 500 Pa
    • Maximum temperature 160F ~ 72C
    • Arrangements 4 and 9

    FUBB Upblast roof exhauster utilizes the FTAB frp fan section with the addition of frp curb cap and frp stack-head including frp dampers to give long life in rugged roof top environments

    Available model sizes (click for details):
    120 150 180 210 240 270 300 330 360 420 480 540 600
    Product Specification
    • Fans to be solid FRP composite construction upblast roof exhauster model FUBB as manufactured by Universal Fan & Blower Ltd. and shall be fabricated in accordance with ASTM Standard Specification D4167-97 (reapproved 2002) for Fiber Reinforced Plastic Fans & Blowers and CGSB 41-GP-22 Standard for Process Equipment.
    • The fan housing utilizes the model FTAB and shall be of solid FRP composite construction, fabricated by open molded methods using vinyl ester resin and glass reinforcements. Glass veil will be used on all airstream surfaces giving a resin rich liner for optimum chemical resistance. Reinforcing flanges shall run the external length of the housing to provide additional strength. The housing shall incorporate integral FRP moulded saddles with 316stainless steel studs cast in place to support a height adjustable motor plate for drive tensioning. The housing shall be flanged for direct connection to the curb cap and stackhead. 
    • An FRP composite stackhead, constructed in a similar method as the fan section and flanged for connection to the fan section will incorporate reinforcement flanges to minimize wind effect and FRP  butterfly dampers suitably positioned  to withstand snow loading. An FRP rain trough which will prevent  ingress of  rain with the dampers in the closed position.
    • An FRP curb cap shall have stiffening gussets to the fan section for use as assembly lifting eyes. 
    • The fan wheel hub and blades shall be of solid FRP composite compression molded vinyl ester resin and glass reinforcement construction. The blades being a true airfoil design to maintain aerodynamic efficiencies. The wheel shall be positively locked onto the shaft by means of a 316ss retaining plate. [Taperlock bushings are not acceptable.]. Wheel shall be statically and dynamically balanced per ANSI/AMCA Standard 204.96 Balance Quality & Vibration Levels for to grade G 6.3.
    • Shafts will be 316ss accurately turned & gauged for accuracy and sized so that the first critical speed is a minimum of 1.35 times the maximum operating speed.
    • Shaft Seal shall be precision cut Teflon for a close tolerance fit to the fan shaft, encased within an FRP seal box with encapsulated 316ss fasteners.
    • Bearings shall be pillow block design sized to have a minimum life of 50,000 hours based on AFMBA L10 standard. Bearings shall be equipped with extended lubrication lines with grease fittings on the outside of the fan housing.
    • All fasteners must be 316 stainless steel construction.
    • Prior to shipment all fans shall be mechanically test run and trim balanced to ensure vibration levels are in keeping with ANSI/AMCA Standard 204.96.

    Note: The addition of UFBL Features to the standard fan will amend the specification accordingly

    Standard Product Specification FUBB-111207

    FWED Wall Exhauster

    FWED Wall Exhauster
    • 10 Sizes : 12.0" to 42.0" 300mm to 1067 mm
    • Volumes : 600 - 36,000 cfm ~ 0.28 - 17.0 m3 /s
    • Pressures : to 2.0" wg ~ 500 Pa
    • Maximum temperature 160F ~ 72C
    • Arrangement 4

    FWED wall exhaust fan complete with frp composite wall sleeve and panel venturi is suitable for general ventilation of corrosive areas such as battery rooms, chemical storage facilities and pulp mills

    Available model sizes (click for details):
    120 150 180 210 240 270 300 330 360 420 480 540 600
    Product Specification
    • Fans to be FRP composite construction panel venturi fan model FWED as manufactured by Universal Fan & Blower Ltd. and shall be fabricated in accordance with ASTM Standard Specification D4167-97 (reapproved 2002) for Fiber Reinforced Plastic Fans & Blowers and CGSB 41-GP-22 Standard for Process Equipment.
    • Fan panel shall be of solid FRP composite construction, fabricated by open molded methods using corrosion grade resins. A ‘C’ glass veil will be used on all airstream surfaces giving a resin rich liner for optimum chemical resistance. The square mounting panel will incorporate a solid FRP composite motor support structured to withstand the torque and loads associated with the required motor size. 
    • The fan wheel shall be solid FRP composite molded construction and of a true airfoil design to maintain aerodynamic efficiencies. The wheel shall be positively locked onto the shaft by means of a 316ss retaining plate. [Taperlock bushings are not acceptable.].No exposed fasteners are permitted The wheel shall be balanced statically and dynamically as per ANSI/AMCA Standard 204.96 Balance Quality & Vibration Levels for Fans to grade G 6.3.
    • Fans will have an FRP wall sleeve having an identical resin & glass system as the fan panel and incorporate an FRP gravity shutter and 304ss removable rear safety screen.
    • All fasteners must be 316 stainless steel construction.
    • The exterior of the fan shall have a grey gel coat finish containing U.V. inhibitor to prevent ultra violet light degradation.
    • Prior to shipment all fans shall be mechanically test run and trim balanced to ensure vibration levels are in keeping with ANSI/AMCA Standard 204.96.
    • All motors shall be severe duty design for airstream service.
    • Performances shall be based on tests made in accordance with AMCA Standard 210 and as stated on the fan schedule. Motor horsepower indicated shall be the minimum size acceptable.

    Note: The addition of UFBL Features to the standard fan will amend the specification accordingly

    Standard Product Specification FWED013008

    Version: 1.18.4.401    Date: September 2018